BAUKNECHT WA 7533/WS-NL
Quick Start

Overview of consumption data GB
approx. Terminate the �Rinse Hold� option:

Temperature Max. Load Water Energy Programme Duration*

Coloured Cotton 60 5.0 39 0.95 2 : 00 � If you do not wish spin clothes, turn programme selector knob to the drain

Cotton 95 5.0 44** 1.60 1 : 55 final spin cycle for the present wash programme.

(°C) (kg) (l) (kWh) (hour : minutes) � Press �Rinse Hold� button again; the programme will terminate automatically with

Coloured Cotton 40 5.0 39 0.55 1 : 45 programme and press the �Start/Pause� button again.

Synthetics 60 2.5 55 0.70 1 : 30 �Spin Speed Reduction� button

Synthetics 40 2.5 50 0.50 1 : 15

� Every programme has an automatic predefined maximum spin speed. � Press the button to set another spin speed. Programme 3.0 35 0.40 0 : 30 � If spin speed �0� selected, the final spinning cancelled. The water is drained Delicates 30 1.5 50 0.50 0 : 45 out only. Wool 1.0 50 0.50 0 : 40

Handwash cold 1.0 0.20 0 : 35

Prewash cycle increases programme duration by approximately 15 min. Consumption values were

PROGRAMME START
Open tap and press button. The pilot lamp of the �Start/Pause� measured normalized conditions in compliance with Standard IEC 60 456. The data on the �Energy button lights up. The indicator lamps show sequence reached in the programme. After Label� refer to programme �Coloured Cotton 60 °C�. Consumption data in the home may vary with

respect values table in relation to water supply pressure and temperature, the load starting programme, the sequence indication runs from left to right through Wash, Rinse, and type wash. Spin. When sequence of programme is finished the corresponding lamp goes out. * The remaining time indicator can similarly deviate from values in the table, because it takes

DOOR LOCK into account the household conditions applicable at that time.
The door can be opened when the �Door Free� indication is shining.

** To reduce temperature, some cold water is added at end main wash cycle, During first 15 minutes of cotton and synthetics programmes the door can be opened

before pump drains the water out. for adding further laundry.

ADD DETERGENT, CLOSE DOOR AND SELECT THE PROGRAMME PROGRAMME END
� The remaining time is on �0:00� and all lights of the programme sequence indication are off. A short audible tone sounds three times. 1. Turn programme selector to the � � position. 2. The programme sequence and the predefined spin speed indication corresponding to 2. Turn the water supply tap off. the selected programme lights up. 3. Open door and unload the machine.

Add detergent as described chapter �Detergent and Additives� in the booklet. 1. Turn selector knob to the desired programme and temperature. � The remaining time display shows duration of the chosen programme (in hours

minutes) and pilot lamp of the �Start/Pause� button is flashing.

PRESS ANY DESIRED OPTION BUTTON(S). The pilot lamp lights up. CHANGE THE AND OPTIONS AFTER PROGRAMME START

An audible tone sounds if the combination of programme, additional options and 1. Press �Start/Pause� button to pause the programme. The light flashes. temperature is not possible. Unsuitable combinations of options are deselected 2. Select the new programme, any options and another spin speed if you want it. automatically. 3. Press �Start/Pause� button again. The new programme continues at the same �Prewash� button position where the previous programme was interrupted. Do not add detergent for this � Only for heavily soiled loads (for example sand, granular dirt) sensible. The cycle time programme. increases by approximately 15 min. �Rinse Hold� button TO CANCEL A PROGRAMME BEFORE THE END � laundry remains in last rinse water without progressing final spin cycle 1. Press �Start/Pause� button to pause the programme. The light flashes. avoid creasing prevent colours from changing. 2. Set programme selector to �Drain�. The spin indicators show �0� and the � This option is particularly recommended for the programme �Synthetics� or �Delicates�. remaining time shows 2 minutes. � This function is particularly useful if you want postpone spinning a later time. 3. Press �Start/Pause� button to start the drain programme. Note: The programme stops to at time the �Rinse Hold� button light flashes.